Motorola VX-P949 User Manual Download | Manualshive

Page: 97 / 112

background image

Customers or end-users in EU countries should contact their local equipment supplier representative or
service centre for information about the waste collection system in their country.

Declaration of Conformity

This declaration is applicable to your radio only if your radio is labeled with the following FCC logo.

Per FCC CFR 47 Part 2 Section 2.1077(a)

Responsible Party

Name: Motorola Solutions, Inc.

Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.

Phone Number: 1-800-927-2744

Hereby declares that

VX-P949

conforms to FCC Part 15, subpart B, section 15.107(a), 15.107(d), and

section 15.109(a)

Class B Digital Device

As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:

1

This device may not cause harmful interference, and

2

This device must accept any interference received, including interference that may cause undesired
operation.

NOTICE:

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio or TV technician for help.

MN003602A01-AF

Legal and Compliance Statement

97

«
...
95
96
97
98
99
...
»

Summary of Contents for VX-P949

















































































































Reviews:

No comments

Related manuals for VX-P949

Brand: Baofeng Pages: 7

Brand: EKO Pages: 12

Brand: Sirius Satellite Radio Pages: 2

Brand: SpotterRF Pages: 2

Brand: Vitek Pages: 24

Brand: Baofeng Pages: 25

Brand: Sangean Pages: 24

Brand: ToooAir Pages: 7

Brand: BTECH Pages: 81

Brand: Bush Pages: 16

Brand: Vertex Standard Pages: 32

Brand: RCA Pages: 15

Brand: Yaesu Pages: 9

Brand: Yaesu Pages: 129

Twintalker 1302

Brand: Topcom Pages: 128

TurboDyne Series

Brand: Rover Pages: 38

Brand: Discovery Expedition Pages: 14

Brand: Quark-Elec Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands