Motorola VX-P949 User Manual Download

Page: 54 / 112

to select the alias or ID, and press the

PTT

button to initiate the call.

If the target radio does not respond after a preprogrammed period, the display shows

Send

page?

d. To send the call alert page, press the

Menu Select

button directly below

Yes

. To exit the

screen without sending the call alert page, press the

Menu Select

button directly below

The display shows

Paging...<Alias>

If the call alert page is sent successfully, you hear a tone and the display shows

Ack

received

. The radio returns to the Home screen.

If the call alert page is not acknowledged, you hear a low tone and the display shows

acknowledge

. Press the

Menu Select

button directly below

to return to the main screen

Contacts

6.6

Quick Call II

This feature allows you to broadcast a series of distinct, recognizable tones before a voice
transmission from the dispatcher or a radio.

The broadcasting dispatcher or radio user can select this pre-programmed alert tone transmission to
be sent to an individual talkgroup or over the entire system. Each tone is distinctive to indicate different
situation or different broadcaster.

NOTICE:

The receiving radios must be configured with the Quick Call II tone in order for the

radio to sound the selected tone and also to sound a preconfigured alert tone after the selected
tone has sound.

6.6.1

Initiating a Quick Call II Transmission

Prerequisites:

The broadcasting or transmitting radio must be pre-programmed to see the tone in the

Quick Call II tone list. The receiving radio must also be pre-programmed to decode the tone to
broadcast.

Procedure:

or to

QCII

, and press the

Menu Select

button directly below

QCII

to select the tone to broadcast.

Press the

PTT

to broadcast the selected tone, or press and hold the

PTT

to broadcast the

selected tone and transmit with your vocal transmission.

You hear the radio sounds the selected tone. You can begin your call after the tone ends.

Release

PTT

to listen.

6.7

Emergency Operation

The Emergency feature is used to indicate a critical situation. An emergency signal overrides any other
communication over the selected channel.

Your radio supports the following Emergency modes:

• Emergency Alarm

MN003602A01-AF
Advanced Features

Summary of Contents for VX-P949
















































































































Search results

Summary of Contents for VX-P949

Reviews:

Related manuals for VX-P949

Brands by name

Popular brands

Motorola VX-P949, User Manual

Search results

Summary of Contents for VX-P949

Reviews:

Related manuals for VX-P949

Brands by name

Popular brands