Motorola VX-P949 User Manual Download

Page: 16 / 112

2.3

Attaching the Antenna

Prerequisites:

Ensure the radio is turned off before attaching the antenna.

Procedure:

Set the antenna in the receptacle.

Turn the antenna clockwise to attach to the radio.

To remove the antenna, turn the antenna counterclockwise.

NOTICE:

When removing the antenna, ensure that the radio is turned off.

2.4

Removing and Attaching the Accessory Connector Cover

The accessory connector is on the antenna side of the radio. It is used to connect accessories to the
radio.

NOTICE:

To prevent damage to the connector, shield it with the connector cover when not in

use.

Procedure:

To remove the accessory connector cover, rotate the thumbscrew counterclockwise until it
disengages from the radio.

NOTICE:

If the thumbscrew is too tight, use an Allen wrench at to loosen it.

Rotate and lift the connector cover to disengage it from the radio.

To attach the accessory connector cover, insert the hooked end of the cover into the slot above
the connector.

Press the top of the cover downward to seat it in the slot.

Tighten by rotating the thumbscrew clockwise by hand.

2.5

Turning On the Radio

Procedure:

Rotate the

On/Off/Volume Control Knob

clockwise until you hear a click.

• If the power-up test is successful, the display shows Motorola Solutions logo momentarily,

followed by the Home screen and the Codeplug Alias.

• If the power-up test is unsuccessful, you see

Error XX/YY

(

XX/YY

is an alphanumeric

code).

NOTICE:

If the radio fails to power-up after repeating a few times, record the

Error XX/YY

code

and contact your dealer.

Codeplug Alias feature is enabled through Customer Programming Software (CPS)
configuration to display the codeplug alias as a temporary text during power on.

MN003602A01-AF
Preparing Your Radio for Use

Summary of Contents for VX-P949
















































































































Search results

Summary of Contents for VX-P949

Reviews:

Related manuals for VX-P949

Brands by name

Popular brands

Motorola VX-P949, User Manual

Search results

Summary of Contents for VX-P949

Reviews:

Related manuals for VX-P949

Brands by name

Popular brands