Motorola VX-P949 User Manual Download | Manualshive

Page: 56 / 112

background image

6.7.4

Exiting Emergency as Supervisor (Trunking Only)

Radios configured as Supervisor are able to cancel emergency mode of other radios. The dispatch
console must be preprogrammed to use this feature. Check with your dealer or system administrator
for more information on dispatch console supporting this feature.

Procedure:

1

Perform one of the following actions:

If…

Then…

If the emergency mode is ini-
tiated by other radios,

press and hold the

Side Button 1

and press the

Emer-

gency

button.

If the emergency mode is ini-
tiated by the Supervisor,

Perform one of the following actions:

• Press and hold the

Emergency

button.

• Press and hold the

Side Button 1

and press the

Emergency

button.

• Wait for console to clear emergency.

NOTICE:

The following buttons combinations are supported:

• Radio

Side Button 1

and

Top (Orange)

button.

• Radio

Side Button 1

and accessory

Orange

button.

• Accessory

1-Dot Button

and radio

Top (Orange)

button.

• Accessory

1-Dot Button

and accessory

Orange

button.

6.7.5

Sending an Emergency Alarm

When and where to use:

This feature allows you to send a data transmission, which identifies the

radio sending the emergency, to the dispatcher.

NOTICE:

The default timer of

Emergency

button press to activate Emergency is milliseconds.

This timer is programmable from milliseconds by a qualified technician.

Procedure:

Press the preprogrammed

Emergency

button.

One of the following scenarios occurs:

• The display shows

Emergency

on the current zone and channel. You hear a short medium-

pitched tone and the LED blinks red momentarily.

• The radio sounds a short low-pitched tone to indicate that the selected channel does not

support emergency and rejects to launch emergency mode.

When you receive the dispatcher’s acknowledgment, the display shows

Ack received

. Four tones

sound, the alarm ends, and the radio exits the Emergency Alarm mode.

If no acknowledgment is received, the display shows

No acknowledge

. The alarm ends when the

timer expires and the radio exits the Emergency Alarm mode.

MN003602A01-AF
Advanced Features

56

«
...
54
55
56
57
58
...
»

Summary of Contents for VX-P949

















































































































Reviews:

No comments

Related manuals for VX-P949

Brand: Elpro Technologies Pages: 62

Brand: C. Crane Pages: 35

Brand: Radio Shack Pages: 12

Brand: SimonsVoss Pages: 16

Brand: König Electronic Pages: 21

Brand: Clatronic Pages: 24

Brand: Uniden Pages: 84

Brand: KIDdesigns Pages: 23

Brand: Vertex Standard Pages: 72

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

AJ3940 - annexe 2

Brand: Philips Pages: 2

Brand: Philips Pages: 12

Brand: Philips Pages: 14

Brand: Philips Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands