Mitsubishi Electric Melservo MR-J5 G Series User Manual Download Page 65 | Manualshive

Page: 65 / 442

background image

2 CONTROL MODE

2.1 Control mode [G] [WG]

63

2

■

Method -6 and -38 (dog type rear end reference homing)

This homing method depends on the timing of reading DOG (Proximity dog) that has detected the rear end of
the proximity dog. Therefore, when the creep speed is set to 100 r/min and homing is performed, the home
position has the following error.



(Encoder resolution)



100/65536 [pulse]

The error in the home position becomes larger as the creep speed increases.

The following figure shows the operation of Homing method -6. The homing direction of Homing method -38 is opposite to that
of Homing method -6.

*1 After the front end of the proximity dog is detected, if the rear end of the proximity dog is detected without reaching the creep speed, [AL.

090] occurs. Revise the length of the proximity dog, or revise both the homing speed and creep speed.

• When homing is started from the proximity dog

• When the servo motor returns at the stroke end

*1 This cannot be used with the software limit.

Statusword bit 10
Target reached

ON
OFF

Statusword bit 12
Homing attained

ON
OFF

0 r/min

ON
OFF
ON
OFF

Controlword bit 4
Homing operation start

*1

Travel distance after proximity dog

+

home position shift distance

Acceleration time
constant

Deceleration time
constant

Homing speed

Creep speed

Forward
rotation

Servo motor speed

3 ms or shorter

Reverse
rotation

Homing position data

Proximity dog

DOG (Proximity dog)

0 r/min

Homing direction

Proximity dog

Servo motor speed

Reverse
rotation

Homing start position

The homing start position is automatically moved back to the position
just before the proximity dog, and homing starts from here.

0 r/min

Homing direction

Stroke end

*1

Proximity dog

Homing start position

Forward
rotation

Servo motor speed

Reverse
rotation

Homing starts from here.

«
...
63
64
65
66
67
...
»

Summary of Contents for Melservo MR-J5 G Series



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Melservo MR-J5 G Series

Brand: JBL Pages: 4

Brand: NAD Pages: 7

Brand: Randall Pages: 9

Brand: NAD Pages: 32

Brand: Yamaha Pages: 8

Brand: Falco Systems Pages: 8

Brand: Rane Pages: 6

Brand: M&S Systems Pages: 44

Brand: Kingray Pages: 6

dPatch SutterPatch

Brand: Sutter Instrument Pages: 2

Brand: YachtConnect Pages: 24

Brand: PRO SIGNAL Pages: 5

Brand: VAC Pages: 11

Brand: icon Audio Pages: 6

Brand: CANARY AUDIO Pages: 9

Brand: Fender Pages: 20

Brand: Fender Pages: 20

Pro-Ject Head Box S

Brand: Pro-Ject Audio Systems Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands