manualshive.com logo in svg

Mitsubishi Electric Melservo MR-J5 G Series, User Manual

The Mitsubishi Electric Melservo MR-J5 G Series offers exceptional performance and precision control in motion control applications. To assist users in harnessing its full potential, we provide a comprehensive and user-friendly User Manual that can be effortlessly downloaded for free from our website. Experience absolute proficiency with ease, courtesy of the MR-J5 G Series User Manual, available exclusively at manualshive.com.

Share
Download
background image

3  BASIC FUNCTION

3.19  Quick stop [G] [WG]

149

3

3.19

Quick stop [G] [WG]

With Quick stop defined in CiA 402, the servo motor can be stopped by the forced stop deceleration. For details of the forced 
stop deceleration, refer to the following.

Page 128 Forced stop deceleration function

When the Quick stop command in [Controlword (Obj. 6040h)] is turned off, the servo motor decelerates to a stop in 
accordance with the setting of [Quick stop option code (Obj. 605Ah)], following which the status changes to "Switch On 
Disabled" (servo-off).

 • This function can be used in the cyclic synchronous mode (csp/csv/cst), profile mode (pp/pv/tq), and 

homing mode (hm).

 • In the torque mode or continuous operation to torque control mode (ct), the servo motor stops with the 

dynamic brake without deceleration to a stop.

Objects for setting

For details on the objects, refer to the User's Manual (Object Dictionary).

The methods and operations supported in [Quick stop option code (Obj. 605Ah)] are shown in the following table.

Index

Sub

Object

Name

Description

6085h

VAR

Quick stop deceleration

Deceleration at deceleration to a stop with Quick stop
Unit: acc units

605Ah

VAR

Quick stop option code

Refer to the following table for the description.

Setting value

Description

1
(not supported)

csp/csv: The servo motor decelerates to a stop with [Quick stop deceleration (Obj. 6085h)], and the state shifts to "Switch On Disabled".
cst/tq: The state shifts immediately to "Switch On Disabled", and the servo motor stops with the dynamic brake.
pp/pv: The servo motor decelerates to a stop with Profile deceleration (6084h) and the state shifts to "Switch On Disabled".
hm: The servo motor decelerates to a stop in accordance with [Homing acceleration (Obj. 609Ah)] and the state shifts to "Switch On 
Disabled".

2

In the cyclic synchronous mode (csp/csv), profile mode (pp/pv), and homing mode (hm), the servo motor decelerates to a stop with [Quick 
stop deceleration (Obj. 6085h)] and the state shifts to "Switch On Disabled".
In the cyclic synchronous torque mode (cst), profile torque mode (tq), and continuous operation to torque control mode (ct), the state 
immediately shifts to "Switch On Disabled" and the servo motor stops with the dynamic brake.

3
(not supported)

The servo motor decelerates by limiting the current, following which the state shifts to "Switch On Disabled".

4
(not supported)

The servo motor decelerates by limiting the voltage, following which the state shifts to "Switch On Disabled".

5
(not supported)

After deceleration to a stop, the state remains as "Quick Stop Active". (Servo-on is maintained.)

6
(not supported)

After deceleration to a stop with [Quick stop deceleration (Obj. 6085h)], the state remains as "Quick Stop Active". (Servo-on is maintained.)

7
(not supported)

After deceleration by limiting the current, the state remains as "Quick Stop Active". (Servo-on is maintained.)

8
(not supported)

After deceleration by limiting the voltage, the state remains as "Quick Stop Active". (Servo-on is maintained.)

Summary of Contents for Melservo MR-J5 G Series



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Melservo MR-J5 G Series

NAD M32 Owner'S Manual preview
M32
Brand: NAD Pages: 24
b2audio Mono Owner'S Manual preview
Mono
Brand: b2audio Pages: 11
A&R A60 Owner'S Handbook Manual preview
A60
Brand: A&R Pages: 16
TEC GLADIATOR Product Manual preview
GLADIATOR
Brand: TEC Pages: 15
ValveTrain Amplification 427 User Manual preview
427
Brand: ValveTrain Amplification Pages: 6
Cloud MA60 Installation And User Manual preview
MA60
Brand: Cloud Pages: 36
VOX Amplification AC2 RhythmVOX Owner'S Manual preview
AC2 RhythmVOX
Brand: VOX Amplification Pages: 16
Rotel RB-1581 Owner'S Manual preview
RB-1581
Brand: Rotel Pages: 16
EBS MICROBASS 3 User Manual preview
MICROBASS 3
Brand: EBS Pages: 5
RM KLV 250 Schematic Diagram preview
KLV 250
Brand: RM Pages: 2
Pro Audio MPC200A User Manual preview
MPC200A
Brand: Pro Audio Pages: 20
NAIM NAIT2 Manual preview
NAIT2
Brand: NAIM Pages: 12
icon Audio Stereo 20 Instructions Manual preview
Stereo 20
Brand: icon Audio Pages: 6
William Sound Pocketalker 2.0 PKT 2.0 User Manual preview
Pocketalker 2.0 PKT 2.0
Brand: William Sound Pages: 20
Channel D SETA L User Manual preview
SETA L
Brand: Channel D Pages: 11
FONESTAR AS-160WRUB Instruction Manual preview
AS-160WRUB
Brand: FONESTAR Pages: 13
Merlaud AMB 80 D Operation & Maintenance Instructions Manual preview
AMB 80 D
Brand: Merlaud Pages: 8
Ssl 1F1500d User Manual preview
1F1500d
Brand: Ssl Pages: 8

Brands by name

Popular brands

Load more brands