Mitsubishi Electric Melservo MR-J5 G Series User Manual Download Page 117 | Manualshive

Page: 117 / 442

background image

3 BASIC FUNCTION

3.11 In-position range setting

115

3

3.11

In-position range setting

The positioning completion status can be checked with INP (in-position). When the number of droop pulses falls within or less
than the range set in servo parameters, INP (in-position) turns on. In addition, the range unit for the in-position and the
conditions to turn on the in-position can be changed with servo parameters.

• INP is always off in the velocity mode, torque mode, and continuous operation to torque control mode.

Precautions

• If the value of [Pr. PA10 In-position range] is set too large and the servo motor is operated at a low speed, INP may always

be turned on. In this case, lower the setting value until the in-position signal stops being outputted.

• After the in-position has fallen to within or below the range, the in-position may turn on and off repeatedly if the droop

pulses exceed the in-position range due to overshoot, vibration, or oscillation. In that case, take actions such as adjusting
the gain and reviewing the operation pattern.

In the super trace control, droop pulses are near 0 during the servo motor control. Thus, the INP (In-position) signal may
remain on. To prevent the INP (In-position) signal from remaining on, set the servo parameters as follows.
[G] [WG]: [Pr. PD13.2 INP output signal ON condition selection] = "1" (Within the in-position range and at the completion of
command output)
[A]: [Pr. PD31.2 INP output signal ON condition selection] = "1" (Within the in-position range and at the completion of
command output)

ON

OFF

ON

OFF

Servo-on command

Occurring

Alarm

Not occurring

Command pulse frequency

Droop pulses

[Pr. PA10 In-position range]

INP (In-position)

«
...
115
116
117
118
119
...
»

Summary of Contents for Melservo MR-J5 G Series



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Melservo MR-J5 G Series

Brand: JBL Pages: 22

Brand: Laney Pages: 14

Brand: Lab.gruppen Pages: 13

Brand: rabbitone Pages: 2

Go Wireless Series

Brand: Vernier Pages: 3

Brand: Coda Pages: 10

Brand: Maxmeen Pages: 8

Brand: Parallel Audio Pages: 12

Brand: EAW Pages: 3

Brand: IC Audio Pages: 25

Brand: MC Crypt Pages: 2

Subwoofer Gadget

Brand: Natural Bass Technology Pages: 2

Brand: Laney Pages: 8

Brand: Harley Benton Pages: 2

Custom Reverb 36WE Georg Wadenius Signature

Brand: Olsson Pages: 8

Brand: B52 Pages: 31

Brand: Fender Pages: 11

Velocity VD 1002

Brand: Blaupunkt Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands