manualshive.com logo in svg

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

The Mitsubishi Electric FR-F700PJ Series is an advanced industrial product designed to deliver exceptional performance and energy efficiency. To ensure seamless operation, it is important to have the Instruction Manual. Download the comprehensive manual for free from manualshive.com and unlock the full potential of your FR-F700PJ Series.

Share
Download
background image

201

Selection of operation mode and operation location

4

P

ARAM

ETE

R

S

(1) Operation mode basics

The operation mode specifies the source of the start command and the frequency command for the inverter.

Basically, there are following operation modes.

External operation mode: For inputting start command and frequency command with an external potentiometer and
switches which are connected to the control circuit terminal.

PU operation mode: For inputting start command and frequency command with the operation panel or parameter unit
(FR-PU04 / FR-PU07).

Network operation mode (NET operation mode): For inputting start command and frequency command with RS-485
communication through PU connector.

The operation mode can be selected from the operation panel or with the communication instruction code.

REMARKS

Either "3" or "4" may be set to select the PU/External combined mode. 

Refer to page 200

 for details.

The stop function (PU stop selection) activated by pressing 

 of the operation panel and parameter unit (FR-PU04/FR-

PU07) is valid even in other than the PU operation mode in the initial setting.
(

Refer to Pr. 75 Reset selection/disconnected PU detection/PU stop selection (page

 

193))

External  
operation mode

Personal computer

Personal computer

FR-PU07

Programmable controller

Potentiometer

Switch

Inverter

GOT

PU connector

1

2

3

4

5 6

7

8

9

10

PU operation mode

Network  

operation mode

PU operation mode

Control terminal

Operation panel

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Reviews:

No comments

Related manuals for FR-F700PJ Series

JED 103 Installation And Operation Manual preview
103
Brand: JED Pages: 4
Vanner IQ Series Owner'S Manual preview
IQ Series
Brand: Vanner Pages: 44
V-TAC 11834 Instruction Manual preview
11834
Brand: V-TAC Pages: 4
Generac Power Systems 1.6L 18 kW Owner'S Manual preview
1.6L 18 kW
Brand: Generac Power Systems Pages: 64
Trace Engineering SW II Datasheet preview
SW II
Brand: Trace Engineering Pages: 2
Sigineer Power M12048D User Manual preview
M12048D
Brand: Sigineer Power Pages: 39
M-Audio Portman 4x4 Manual preview
Portman 4x4
Brand: M-Audio Pages: 45
GALAGAR 160 PFC Technical Instruction Manual preview
160 PFC
Brand: GALAGAR Pages: 28
Humandata USB-301 User Manual preview
USB-301
Brand: Humandata Pages: 10
CMP PowerClean Salt Econ Installation Instructions & Product Manual preview
PowerClean Salt Econ
Brand: CMP Pages: 24
Daihen OTC WB-P400 Owner'S Manual preview
OTC WB-P400
Brand: Daihen Pages: 158
Davis Instruments 6614 User Manual preview
6614
Brand: Davis Instruments Pages: 24
Carbest 814136 User Instruction preview
814136
Brand: Carbest Pages: 22
ICP DAS USA tSH-700 Series Firmware Update preview
tSH-700 Series
Brand: ICP DAS USA Pages: 21
SHOWTEC Node-1 Manual preview
Node-1
Brand: SHOWTEC Pages: 16
RS FMC-ST RS Instruction Leaflet preview
FMC-ST RS
Brand: RS Pages: 8
Interlogix IFS MCR200-1T-1TW User Manual preview
IFS MCR200-1T-1TW
Brand: Interlogix Pages: 23
Procon MelcoRETAIL MINI Instruction Manual preview
MelcoRETAIL MINI
Brand: Procon Pages: 48

Brands by name

Popular brands

Load more brands