Mitsubishi Electric FR-F700PJ Series Instruction Manual Download Page 283

Page: 283 / 356

278

Setting the parameter unit and operation panel

4.23.3 Setting dial potentiometer mode/key lock selection (Pr. 161)

The above parameter can be set when

Pr. 160 Extended function display selection

= "0".

(Refer to page 197)

(1) Setting the frequency with the setting dial

The setting dial of the operation panel can be used for setting like a potentiometer.
The key operation of the operation panel can be disabled.

Parameter

Number

Name

Initial Value

Setting

Range

Description

161

Frequency setting/key lock
operation selection

Setting dial frequency
setting mode

Key lock invalid

Setting dial
potentiometer mode

Setting dial frequency
setting mode

Key lock valid

Setting dial
potentiometer mode

Operation example Operate at 30Hz.

Operation

Display

1. Screen at power-ON

The monitor display appears.

2. Operation mode change

Press

to choose the PU operation mode.

PU indicator is lit.

3. Frequency setting

Turn

to show the frequency you want to set. The frequency

flickers for about 5s.

While the value is flickering, press

to set the frequency.

(If

is not pressed, the indication of the value goes back to

" (0.00Hz) after about 5s of flickering. In that case, go back

to “operation step 3”, and set the frequency again.)
After about 3s of flickering, the indication of the value goes back to "

" (monitor display).

Flicker

···

Frequency setting complete!!

After 3s, the monitor display

appears.

5. Start





acceleration





constant speed

Press

to start operation.

The frequency value on the display increases in

Pr. 7 Acceleration

time

, and "

" (30.00Hz) appears.

To change the set frequency, perform the operation in above step 3 and 4. (Starting from the previously set frequency.)

7. Deceleration





stop

Press

to stop. The frequency value on the indication

decreases in

Pr. 8 Deceleration time

, and the motor stops rotating

with "

"(0.00Hz) displayed.

REMARKS



is not pressed within 5s after

is turned, the operation may not performed at the set frequency.

Flickers for about 5s

Stop

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Search results

Summary of Contents for FR-F700PJ Series

Reviews:

Related manuals for FR-F700PJ Series

Brands by name

Popular brands

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

Search results

Summary of Contents for FR-F700PJ Series

Reviews:

Related manuals for FR-F700PJ Series

Brands by name

Popular brands