Mitsubishi Electric FR-F700PJ Series Instruction Manual Download Page 288

Page: 288 / 356

283

FR-E500 series operation panel (PA02) setting

4.24 FR-E500 series operation panel (PA02) setting

The operation panel (PA02) for the FR-E500 series can be hooked up with the PU cable for use.
(The inverter can not be directly connected.)

4.24.1 Built-in potentiometer switching (Pr. 146)

Purpose

Parameter that should be Set

Refer to Page

Select the frequency setting method
of the operation panel (built-in

potentiometer, key)

Frequency setting
command selection

Pr. 146

283

Set the magnitude (slope) of the
output frequency by the built-in
potentiometer as desired.

Built-in frequency setting
potentiometer bias/gain

C22(Pr. 922), C23(Pr. 922),

C24(Pr. 923), C25(Pr. 923)

284

Switches the frequency setting method between the PA02 built-in frequency setting potentiometer and digital frequency

setting by the

key.

Parameter

Number

Name

Initial Value

Setting Range

Description

146

Built-in potentiometer
switching



PA02 built-in frequency setting potentiometer valid
Frequency setting by the built-in frequency setting
potentiometer

PA02 built-in frequency setting potentiometer invalid

Digital frequency setting by the

key.

Changing frequency continuously by pressing the

key.

Hold down the

key to perform

operation.



Set when performing operation using the built-in frequency setting potentiometer using the operation panel (PA02) for the FR-E500 series.
Operation from the inverter operation panel or communication is not available.

The above parameter can be set when

Pr.160 Extended function display selection

= "0".

(Refer to page 197)

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Search results

Summary of Contents for FR-F700PJ Series

Reviews:

Brands by name

Popular brands

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

Search results

Summary of Contents for FR-F700PJ Series

Reviews:

Brands by name

Popular brands