Mitsubishi Electric FR-F700PJ Series Instruction Manual Download Page 284

Page: 284 / 356

279

Setting the parameter unit and operation panel

ARAM

ETE

(2) Using the setting dial like a potentiometer to set the frequency

Operation example Change the frequency from 0Hz to 60Hz during operation

Operation Display

1. Screen at power-ON

The monitor display appears.

Press

to choose the PU operation mode.

PU indicator is lit.

Press

to choose the parameter setting

mode.

PRM indicator is lit.

(The parameter number read previously

appears.)

Turn

until

(Pr. 160)

appears.

Press

to read the present set value.

"(initial value) appears.

Turn

to change it to the set value "

Press

to set.

Flicker

···

Parameter setting complete!!

Change

Pr. 161

to the setting value of "

in the similar manner. (Refer to step 4 to 7.)

Flicker

···

Parameter setting complete!!

Mode/monitor check

Press

twice to choose the monitor/

frequency monitor.

10.

Press

to start the inverter.

11.

Turn

until "

" appears.

The flickering frequency is the set frequency.

You need not press

The frequency flickers for about 5s.

REMARKS



If the display changes from flickering "60.00" to "0.00", the setting of

Pr. 161 Frequency setting/key lock operation selection

may not

be "1".



Independently of whether the inverter is running or at a stop, the frequency can be set by merely turning the dial.



When the frequency is changed, it will be stored in EEPROM as the set frequency after 10s.

NOTE



When using the setting dial under general-purpose motor control, the frequency goes up to the set value of

Pr.1

Maximum frequency

(initial value:120Hz). When using the setting dial under IPM motor control, the frequency goes up

to the set value of the maximum motor speed (frequency).
Adjust the setting of

Pr.1 Maximum frequency

according to the application.

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Search results

Summary of Contents for FR-F700PJ Series

Reviews:

Related manuals for FR-F700PJ Series

Brands by name

Popular brands

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

Search results

Summary of Contents for FR-F700PJ Series

Reviews:

Related manuals for FR-F700PJ Series

Brands by name

Popular brands