Mitsubishi Electric FR-F700PJ Series Instruction Manual Download Page 149

Page: 149 / 356

144

Function assignment of external terminal and control

4.11.6 Detection of output frequency (SU, FU signal, Pr. 41 to Pr. 43, Pr. 870)

The inverter output frequency is detected and output at the output signals.

Parameter

Number

Name

Initial Value

Setting Range

Description

Up-to-frequency
sensitivity

10%

0 to 100%

Level where the SU signal turns ON.

Output frequency
detection

6Hz

0 to 400Hz

Frequency where the FU signal turns ON.

Output frequency
detection for reverse
rotation

9999

0 to 400Hz

Frequency where the FU signal turns ON in reverse
rotation.

9999

Same as

Pr. 42

setting

870

Speed detection
hysteresis

0Hz



0 to 5Hz

Set the hysteresis width for the detected frequency.

The above parameters can be set when

Pr. 160 Extended function display selection

= "0".

(Refer to page 197)



Performing IPM parameter initialization changes the settings.

(Refer to page 85)

(1) Up-to-frequency sensitivity (SU signal,

Pr. 41

)



When the output frequency reaches the set frequency, the
up-to-frequency signal (SU) is output.



The

Pr. 41

value can be adjusted within the range 0% to



100% on the assumption that the set frequency is 100%.



This parameter can be used to ensure that the running
frequency has been reached to provide the operation start
signal etc. for related equipment.



When using the SU signal, set "1 (positive logic) or 101
(negative logic)" in

Pr.190 or Pr.192 (output terminal function

selection)

to assign function to the output terminal.

(2) Output frequency detection

(FU signal,

Pr. 42, Pr. 43

)



The output frequency detection signal (FU) is output when
the output frequency reaches or exceeds the

Pr. 42

setting.



This function can be used for electromagnetic brake
operation, open signal, etc.



Frequency detection that is dedicated to the reverse
operation can be set by setting detection frequency to

Pr. 43

This function is effective for switching the timing of
electromagnetic brake operation between forward rotation
(rise) and reverse rotation (fall) during vertical lift operation,
etc.



When

Pr. 43





"9999", the

Pr. 42

setting is used for forward

rotation and the

Pr. 43

setting is used for reverse rotation.



When using the FU signal, set "4 (positive logic)" or "104

(negative logic)" to

Pr.190 or Pr.192 (output terminal function

selection)

to assign the function to the output terminal.

Output frequency

(Hz)

Set frequency

Adjustment
range

Pr.41

Time

OFF

Output signal

Forward
rotation

Reverse
rotation

Time

Output frequency (Hz)

OFF

Pr.43

Pr.42

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Search results

Summary of Contents for FR-F700PJ Series

Reviews:

Related manuals for FR-F700PJ Series

Brands by name

Popular brands

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

Search results

Summary of Contents for FR-F700PJ Series

Reviews:

Related manuals for FR-F700PJ Series

Brands by name

Popular brands