manualshive.com logo in svg

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

Share
Download
Mitsubishi Electric FR-F700PJ Series Instruction Manual Download Page 174

169

Operation selection at power failure and instantaneous power failure

4

P

ARAM

ETE

R

S

(4) Operation continuation at instantaneous power failure function (

Pr. 261 

= "2")

When power is restored during deceleration after a power failure, acceleration is made again up to the set frequency.

When this function is used in combination with the automatic restart after instantaneous power failure function (

Pr. 57

"9999"), deceleration can be made at a power failure and acceleration can be made again after power restoration.

(5) Power failure deceleration signal (Y46 signal)

The Y46 signal is ON during deceleration at an instantaneous power failure or during a stop after deceleration at an

instantaneous power failure.

After a power failure stop, the inverter can not start even if power is restored and the start command is given. In this case,

check the power failure deceleration signal (Y46 signal). (at occurrence of input phase loss (E.ILF), etc.)

For the Y46 signal, set "46 (forward operation)" or "146 (reverse operation)" to 

Pr. 190 or Pr. 192 (output terminal function

selection) 

to assign the function.

*   Acceleration time depends on 

Pr. 7 (Pr. 44)

.

NOTE

When operation continuation at instantaneous power failure function is used, keep the starting signal (STF/STR) ON
even during instantaneous power failure. If the starting signal turns OFF during instantaneous power failure, the
inverter decelerates according to the deceleration time setting, causing the motor to coast if enough regenerative
energy is not obtained.

REMARKS

During a stop or trip, the power failure stop selection is not performed.

NOTE

Changing the terminal assignment using 

Pr. 190 and Pr. 192 (output terminal function selection)

 may affect the other

functions. Set parameters after confirming the function of each terminal.

The power failure deceleration stop function is unavailable under IPM motor control regardless of the 

Pr. 261

 setting.

CAUTION

Even if the power failure stop function is valid, some loads may cause the inverter to trip and the motor to 
coast.
The motor will coast if enough regenerative energy is not given from the motor to the inverter.

Parameters referred to

Pr. 57 Restart coasting time 

 

Refer to page 161

Pr. 190, Pr. 192 (output terminal function selection) 

 

Refer to page 140

Y46

During deceleration at 
occurrence of power failure

Reacceleration

Time

When power is restored during deceleration  
at occurrence of power failure

Output 

frequency

IPF

Power

Pr. 261

 = 2

Time

Output 

frequency

Y46

Automatic restart  
after instantaneous 
power failure

Reset time + 

Pr. 57

When used with automatic restart  
after instantaneous power failure

During power failure

Power

Pr. 261

 = 2, 

Pr. 57

    9999

During deceleration at 
occurrence of power failure

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands