manualshive.com logo in svg

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

The Mitsubishi Electric FR-F700PJ Series is an advanced industrial product designed to deliver exceptional performance and energy efficiency. To ensure seamless operation, it is important to have the Instruction Manual. Download the comprehensive manual for free from manualshive.com and unlock the full potential of your FR-F700PJ Series.

Share
Download
background image

159

Monitor display and monitor output signal

4

P

ARAM

ETE

R

S

4.12.5 How to calibrate the terminal FM when using the operation panel

Perform the following procedure to calibrate terminal FM using the operation panel FR-DU07. 

Refer to page 158

 for

the details of parameters. 

Operation Display 

1.

Confirm the operation status indicator and 

operation mode indicator

(When

 Pr. 54

 

= 1)

2.

Press 

 to choose the parameter setting 

mode.

PRM indicator is lit.

(The parameter number read previously appears.)

3.

Turn  

until 

 

appears.

4.

Press 

 to read the present set value.

"

" (initial value) appears.

5.

Turn 

 to change it to the setting value of 

" ".

6.

Press  

to 

set.

Flicker...Parameter setting complete!!

7.

Turn  

until 

 

appears.

8.

Press  

to 

display 

.

9.

Turn  

until 

 

appears.

Set to 

C0 FM terminal calibration.

10.

Press 

 to enable setting.

11.

If the inverter is at a stop, press the 

 key 

to start the inverter.
(Motor needs not be connected.)

12.

Turn 

 to adjust the indicator needle to 

the desired position.

Analog indicator

13.

Press

.

Setting is complete.

Flicker...Parameter setting complete!!

Turn 

 to read another parameter.

Press 

 to return to the 

 indication (step 8).

Press 

 twice to show the next parameter (

).

C0 to C7 settings 
are enabled.

The monitor set to 

Pr. 54

 

FM terminal function selection

 

is displayed.

Hz

A

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Reviews:

No comments

Related manuals for FR-F700PJ Series

Datel 20A Specification Sheet preview
20A
Brand: Datel Pages: 22
Lampizator Fezz Equinox EVO User Manual preview
Fezz Equinox EVO
Brand: Lampizator Pages: 5
Allen-Bradley 844D-A Series Installation Instructions preview
844D-A Series
Brand: Allen-Bradley Pages: 4
Tvone 1T-VS-558 Instruction Manual preview
1T-VS-558
Brand: Tvone Pages: 16
GALCO EL110T User Manual preview
EL110T
Brand: GALCO Pages: 8
Raymarine E70196 Installation Instructions Manual preview
E70196
Brand: Raymarine Pages: 42
Midea MDV-120W/DON1 Technical & Service Manual preview
MDV-120W/DON1
Brand: Midea Pages: 86
Schumacher Electric PI-200 Owner'S Manual preview
PI-200
Brand: Schumacher Electric Pages: 40
R3Di RS3600 User Manual preview
RS3600
Brand: R3Di Pages: 10
HEIDENHAIN LIF 481R Mounting Instructions preview
LIF 481R
Brand: HEIDENHAIN Pages: 36
Optical Systems Design OSD2153 Series Operator'S Manual preview
OSD2153 Series
Brand: Optical Systems Design Pages: 20
Interlogix IFS MCR200-1T-1TW User Manual preview
IFS MCR200-1T-1TW
Brand: Interlogix Pages: 23
PEC MACC Manual preview
MACC
Brand: PEC Pages: 26
ICP DAS USA tM-7520U Quick Start Manual preview
tM-7520U
Brand: ICP DAS USA Pages: 2
Felicitysolar IVGM4648 User Manual preview
IVGM4648
Brand: Felicitysolar Pages: 17
Draper IN1000 Instructions Manual preview
IN1000
Brand: Draper Pages: 16
4Patriots Patriot Power Generator 1800 User Manual preview
Patriot Power Generator 1800
Brand: 4Patriots Pages: 32
DeWalt D55040 Quick Start Manual preview
D55040
Brand: DeWalt Pages: 2

Brands by name

Popular brands

Load more brands