manualshive.com logo in svg

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

Share
Download
Mitsubishi Electric FR-F700PJ Series Instruction Manual Download Page 216

211

Selection of operation mode and operation location

4

P

ARAM

ETE

R

S

4.19.3 Setting the frequency by the operation panel (

Pr. 79 

= 3)

POINT

Switch ON the STF(STR) signal to give a start command.

Use the operation panel (

) to give a frequency command.

Set "3" (External/PU combined operation mode 1) in

 Pr. 79 

.

Operation 
example

Operate at 30Hz.

Operation Display 

1.

Screen at power-ON

The monitor display appears.

2.

Change the

 Pr. 79 

setting to "3". (Refer to page 

60 

for change of the setting.)

[PU] indicator and [EXT] indicator are lit.

3.

Turn 

 to show the frequency you want to set.

The frequency flickers for about 5s.

4.

While the value is flickering, press 

 to set the 

frequency. 
After the value flickered for about 3s, the display 

returns to "

" (monitor display).

(If you do not press

, the value flickers for about 

5s and the display then returns to "

" (0.00Hz). 

At this time, return to "Step 3" and set the frequency 
again.)

Flicker...frequency setting complete!!

The monitor display appears after 3s.

5.

Start 

 acceleration 

 constant speed

Turn the start switch (STF or STR) ON.
The frequency value on the display increases in 

Pr. 7 

Acceleration time, and

 "

" (30.00Hz) appears.

[RUN] indicator is lit during forward rotation operation 
and flickers during reverse rotation operation.

6.

To change the set frequency, perform the operation in above steps 3 and 4. (Starting from the previously set frequency.)

7.

Deceleration 

 stop

Turn OFF the start switch (STF or STR). The 
frequency value on the indication decreases in 

Pr. 8 

Deceleration time, 

and the motor stops rotating with 

"

" (0.00Hz) displayed.

[RUN] turns OFF.

REMARKS

Pr. 178 STF terminal function selection

 must be set to "60" (or 

Pr. 179 STR terminal function selection 

must be set to "61"). 

(all are initial values)

When

 Pr. 79 Operation mode selection 

is set to "3", multi-speed operation

 (Refer to page 106) 

is also valid.

 Pressing 

 to stop the motor and the display shows 

. 

1. Turn the start switch (STF or STR) OFF.

2. The display can be reset by 

.

SD

STF
STR

Inverter

Operation  

panel

Forward rotation start

Reverse rotation start

[Connection diagram]

Flickers for about 5s

Forward  
rotation

Reverse 
rotation

ON

Forward  
rotation

Reverse 
rotation

OFF

Stop

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands