Mitsubishi Electric FR-F700PJ Series Instruction Manual Download Page 191

Page: 191 / 356

186

Frequency setting by analog input (terminal 2, 4)

4.17.2 Setting the frequency by analog input (voltage input)

POINT



Switch ON the STF (STR) signal to give a start command.



Use the (frequency setting) potentiometer to give a frequency command.

[Connection diagram]

(The inverter supplies 5V power to the frequency
setting potentiometer. (terminal 10))

Operation example

Operate at 60Hz.

Operation

Display

Screen at power-ON

The monitor display appears.

Start

Turn ON the start switch (STF or STR).
[RUN] indicator flickers fast because the
frequency command is not given.

Acceleration



constant speed

Turn the potentiometer clockwise slowly to full.
The frequency value on the display increases in

Pr. 7 Acceleration time,

and "

" (60.00Hz)

appears.
[RUN] indicator is lit during forward rotation
operation and flickers slowly during reverse
rotation operation.

Deceleration

Turn the potentiometer counterclockwise slowly to
full.
The frequency value on the display decreases in

Pr. 8 Deceleration time,

and the motor stops rotating

with "

" (0.00Hz) displayed.

[RUN] flickers fast.

Stop

Turn OFF the start switch (STF or STR).
[RUN] indicator turns OFF.

Forward rotation start

Reverse rotation start

Inverter

STF
STR
SD

Frequency
setting
potentiometer

Forward
rotation

Reverse
rotation

Flickering

Stop

Forward
rotation

Reverse
rotation

OFF

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Search results

Summary of Contents for FR-F700PJ Series

Reviews:

Brands by name

Popular brands

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

Search results

Summary of Contents for FR-F700PJ Series

Reviews:

Brands by name

Popular brands