manualshive.com logo in svg

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

Share
Download
Mitsubishi Electric FR-F700PJ Series Instruction Manual Download Page 177

172

Operation setting at fault occurrence

4.14.2 Input/output phase loss protection selection (Pr. 251, Pr. 872)

(1) Output phase loss protection selection 

(Pr. 251)

 If phase loss occurs during inverter operation (except for during DC brake operation, or output frequency is 1Hz or less),

output phase loss protection (E.LF) activates, and inverter trips.

 When 

Pr. 251  

is set to "0", output phase loss protection (E.LF) becomes invalid.

(2) Input phase loss protection selection

 

(Pr. 872)

 When 

Pr. 872 

is set to "1", input phase loss protection (E.ILF) is provided if a phase loss of one phase among the three

phases is detected for 1s continuously.

4.14.3 Earth (ground) fault detection at start (Pr. 249)

You can choose whether to make Input/output phase loss protection valid or invalid. 

Output phase loss protection is a function to stop the inverter output if one of the three phases (U, V, W) on the
inverter's output side is lost.

Input phase loss protection is a function to stop the inverter output if one of the three phases (R/L1, S/L2, T/L3) on the
inverter's input side is lost.

Parameter 

Number

Name

Initial Value

Setting Range

Description

251

Output phase loss 
protection selection

1

0

Without output phase loss protection

1

With output phase loss protection

872

Input phase loss protection 
selection

0

0

Without input phase loss protection

1

With input phase loss protection

The above parameters can be set when 

Pr. 160 Extended function display selection 

= "0". 

(Refer to page 197)

NOTE

If an input phase loss continues for a long time, the converter section and capacitor lives of the inverter will be
shorter.

If the load is light or during a stop, lost phase cannot be detected because detection is performed based on the
fluctuation of bus voltage. Large unbalanced phase-to-phase voltage of the three-phase power supply may also
cause input phase loss protection (E.ILF).

Phase loss can not be detected during regeneration load operation.

You can choose whether to make earth (ground) fault detection at start valid or invalid. Earth (Ground) fault detection is
executed only right after the start signal is input to the inverter.
Protective function will not activate if an earth (ground) fault occurs during operation.

Parameter 

Number

Name

Initial Value

Setting Range

Description

249

Earth (ground) fault 
detection at start

0

0

Without earth (ground) fault detection

1

With earth (ground) fault detection

The above parameter can be set when 

Pr. 160 Extended function display selection 

= "0". 

(Refer to page 197)

NOTE

As detection is executed at start, output is delayed for approx. 20ms every start.

If an earth (ground) fault is detected with "1" set in

 Pr. 249

, output side earth (ground) fault overcurrent (E.GF) is detected and

the inverter trips. (

Refer to page 305)

If the motor capacity is smaller than the inverter capacity when using the 5.5K or higher, earth (ground) fault detection may not
be provided.

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands