manualshive.com logo in svg

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

The Mitsubishi Electric FR-F700PJ Series is an advanced industrial product designed to deliver exceptional performance and energy efficiency. To ensure seamless operation, it is important to have the Instruction Manual. Download the comprehensive manual for free from manualshive.com and unlock the full potential of your FR-F700PJ Series.

Share
Download
background image

200

Selection of operation mode and operation location

4.19 Selection of operation mode and operation location

4.19.1 Operation mode selection (Pr. 79)

The above parameter can be changed during a stop in any operation mode.

Purpose

Parameter that should be Set

Refer to Page

Operation mode selection

Operation mode selection

Pr. 79

200

Started in Network operation mode Operation mode at power-on

Pr. 79, Pr. 340

213

Selection of operation location

Operation command source and 

speed command source during 
communication operation, selection 

of operation location

Pr. 338, Pr. 339

Pr. 551

214

Used to select the operation mode of the inverter.

Mode can be changed as desired among operation using external command signals (External operation), operation

from the operation panel and PU (FR-PU07/FR-PU04) (PU operation), combined operation of PU operation and

External operation (External/PU combined operation), and Network operation (when RS-485 communication is used).

Parameter 

Number

Name

Initial Value

Setting Range

79

Operation mode selection

0

0 to 4, 6, 7

POINT

Use the easy setting mode to set 

Pr. 79

 in simple steps. 

(Refer to page 60)

Pr.79

Setting

Description

LED Indication

: OFF     

: ON

Refer 

to 

Page

0 

(Initial 
value)

Use External/PU switchover mode (At power ON, the inverter is in the External operation 
mode.)

Press 

 to switch between the PU and External operation mode.

PU operation mode

External operation mode

NET operation mode

204

1

Operation mode

Frequency command

Start command

PU operation mode

204

PU operation mode (fixed)

Setting by the operation 
panel and PU (FR-PU04/FR-
PU07)

Input by 

 on the 

operation panel or 

 and 

 on PU (FR-PU04/FR-

PU07)

2

External operation mode (fixed)
The operation can be performed 
by switching between the 
External and NET operation 
modes.

External signal input (from 
terminal 2, 4, JOG, multi-
speed selection, etc.) 

External signal input (from 
terminal STF and STR)

External operation mode

NET operation mode

204

3

External/PU combined 
operation mode 1

Operation panel and PU (FR-
PU04/FR-PU07) setting or 
external signal input (multi-
speed setting, across 
terminals 4 and 5 (valid when 
AU signal turns ON)). 

*

External signal input (from 
terminal STF and STR)

External/PU combined 
operation mode

205

4

External/PU combined 
operation mode 2

External signal input
(Terminal 2, 4, JOG, multi-
speed selection, etc.)

Input by 

 on the 

operation panel or 

 and 

 on PU (FR-PU04/FR-

PU07)

205

6

Switchover mode
Switch among PU operation, External operating, and NET operation while keeping the
same operating status.

PU operation mode

External operation mode

NET operation mode

206

7

External operation mode (PU operation interlock)
X12 signal ON: Operation mode can be switched to the PU operation mode.

(output stop during External operation)

X12 signal OFF: Operation mode cannot be switched to the PU operation mode.

206

The priorities of the frequency commands when 

Pr. 79

 = "3" are "Multi-speed operation (RL/RM/RH/REX) > PID control (X14) > terminal 4 analog input (AU)

> digital input from the operation panel".

REMARKS

If switching of the operation mode is invalid even though 

Pr. 79 

is set, 

refer to page 314

.

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Reviews:

No comments

Related manuals for FR-F700PJ Series

Samson 6111 Mounting And Operating Instructions preview
6111
Brand: Samson Pages: 28
A2Z Ozone Systems Aquatic 2 Installation & Operation Manual preview
Aquatic 2
Brand: A2Z Ozone Systems Pages: 13
A2Z Ozone MP-1000 Operating Manual preview
MP-1000
Brand: A2Z Ozone Pages: 17
Kaco blueplanet 29.0 TL3 Series Operating Instructions Manual preview
blueplanet 29.0 TL3 Series
Brand: Kaco Pages: 64
Vector Industrial Series VEC023 Owner'S Manual & Warranty Information preview
Industrial Series VEC023
Brand: Vector Pages: 8
Huahuan Electronics H0FL-EthMux.SA1601 User Manual preview
H0FL-EthMux.SA1601
Brand: Huahuan Electronics Pages: 55
Bang & Olufsen Beosound 2000 User Manual preview
Beosound 2000
Brand: Bang & Olufsen Pages: 12
Allied Telesis AT-GS2002/SP Installation Manual preview
AT-GS2002/SP
Brand: Allied Telesis Pages: 52
Baumer Hubner Berlin CANopen PMG 10 Installation And Operating Instructions Manual preview
Hubner Berlin CANopen PMG 10
Brand: Baumer Pages: 28
TRENDnet 1550nm Quick Installation Manual preview
1550nm
Brand: TRENDnet Pages: 12
Fuji Electric FRN0001C2S-2A FRN0002C2S-2A FRN0004C2S-2A FRN0006C2S-2A FRN0010C2S-2A FRN0012C2S-2A FRN0020C2S-2A FRN0025C2S-2A FRN0033C2S-2A FR Instruction Manual preview
FRN0001C2S-2A FRN0002C2S-2A FRN0004C2S-2A FRN0006C2S-2A FRN0010C2S-2A FRN0012C2S-2A FRN0020C2S-2A FRN0025C2S-2A FRN0033C2S-2A FR
Brand: Fuji Electric Pages: 263
Asian Electron PIC2KVA Series Instruction Manual preview
PIC2KVA Series
Brand: Asian Electron Pages: 16
Fuji Electric FRENIC-Multi FRN0.1E1S-2LM1 Starting Manual preview
FRENIC-Multi FRN0.1E1S-2LM1
Brand: Fuji Electric Pages: 33
Motrona IT251 Operating Manual preview
IT251
Brand: Motrona Pages: 16
Digitus DN-82110-1 User Manual preview
DN-82110-1
Brand: Digitus Pages: 3
Analog Devices LTC7810ELXE Demo Manual preview
LTC7810ELXE
Brand: Analog Devices Pages: 10
DAB MCE-110/C Instruction For Installation And Maintenance preview
MCE-110/C
Brand: DAB Pages: 18
Xantrex XPower 500 Owner'S Manual preview
XPower 500
Brand: Xantrex Pages: 36

Brands by name

Popular brands

Load more brands