MIMAKI TS3-1600, Operation Manual

Page: 175 / 206

5-11
Warning / Error Messages
5
T
rouble
shoot
ing
Message Cause Solution
An error occurred in the wiper
control.
Turn off the main power to the machine
and turn it on after a while.
If the same error message appears again,
contact your local distributor to call for
service.
Paper could not be detected.
The media set position or media
itself is not proper.
If the same error message appears again
even after setting the media properly,
contact your local distributor to call for
service.
The set position of the media is not
proper. The media detection has not
completed.
Set the media to the proper position again.
(
P.2-8
、
P.2-14)
Y-origin could not be detected.
Turn off the main power to the machine
and turn it on after a while.
If the same error message appears again,
contact your local distributor to call for
service.
The ambient temperature is out of
the usable temperature range (too
low).
Adjust the ambient temperature of the
installation place. (
P.3-38)
The ambient temperature is out of
the usable temperature range (too
high).
There is a slot where no cartridge
has been inserted.
Set a cartridge.
An error occurred on the head unit
memory.
Turn off the main power to the machine
and turn it on after a while.
If the same error message appears again,
contact your local distributor to call for
service.
The head is not connected.
An error occurred on the head slider
board.
The head is not MIMAKI genuine.
A SD-RAM of the size required for
the machine has not been
equipped.
Turn off the main power to the machine
and turn it on after a while.
If the same error message appears again,
contact your local distributor to call for
service.
(When a usable SD-RAM is available, the
machine can be started as is. However, a
printing speed may be slow depending on
resolution. )
An abnormal voltage of head was
detected.
Turn off the main power to the machine
and turn it on after a while.
If the same error message appears again,
contact your local distributor to call for
service.
An error is detected on the wave-
form printed on the lower line of the
display.
Model ID of main PCB is different.
(XX is ID code.)
* * * * * E R ROR 4 6 * * * * *
W I P E R
* * * * * E R ROR 5 0 * * * * *
ME D I A W I D T H S E N SOR
* * * * * E R ROR 5 0 * * * * *
ME D I A S E T POS I T I ON L
* * * * * E R ROR 5 0 * * * * *
ME D I A S E T POS I T I ON R
* * * * * E R ROR 5 1 * * * * *
Y - OR I G I N
* * * * E RROR 1 2 0 * * * *
ROOM T EMP L OW ( X X
° C )
* * * * E RROR 1 2 1 * * * *
ROOM T EMP H I GH ( X X ° C )
* * * * E RROR 1 4 4 * * * *
C A R T R I DGE S E T !
* * * * E RROR 2 0 0 * * * *
H E A D MEMOR Y ( - - - - )
* * * * E RROR 2 0 2 * * * *
D V E I C E CON S T RUC T I ON
* * * * E RROR 2 0 3 * * * *
S DR AM S I Z E
* * * * E RROR 2 0 5 * * * *
4 2 V H E A D V o l t a g e
* * * * E RROR 2 0 7 * * * *
X X X X X X X X X X
* * * * E RROR 2 0 8 * * * *
CH E C K MA I N P C B I D X X