Miele G 7960 C SCVi Operating Instructions Manual Download Page 44 | Manualshive

Page: 44 / 124

background image

Settings

44

Refill reminders

If you only ever use combination
detergent products or automatic
dispensing using Miele PowerDisks (if
available), you can switch off the refill
reminders for dishwasher salt and rinse
aid if you wish.

Please make sure that if you stop
using combination detergents, you
refill the dishwasher salt and rinse
aid. Switch the refill reminders back
on.

AutoOpen

In some programmes the door
automatically opens slightly to assist
the drying process.

This function can be deactivated if you
wish.



Risk of damage due to steam.

Steam from the dishwasher could
damage the edges of delicate
worktops when you open the door at
the end of the programme if the fan
is no longer running.
If you have deactivated the
automatic door opening function but
would still like to open the door at
the end of the programme, then
make sure that you open the door
fully.

Knock2open

The door opens if you knock twice in
quick succession on the top third of the
door front.

The function can be deactivated,
in which case the door has to be fitted
with a handle to open it.

«
...
42
43
44
45
46
...
»

Summary of Contents for G 7960 C SCVi





























































































































Reviews:

No comments

Related manuals for G 7960 C SCVi

Brand: Zanussi Pages: 28

Brand: Sammic Pages: 48

DW60A807 Series

Brand: Samsung Pages: 420

Brand: DAEWOO ELECTRONICS Pages: 28

Brand: ZEP Pages: 36

Brand: Glen Dimplex Pages: 48

Appliances Profile PFWS4605

Brand: GE Pages: 88

Brand: GE Pages: 12

Brand: Bartscher Pages: 18

Brand: VALBERG Pages: 92

Brand: Supera Pages: 15

Brand: CaterChef Pages: 44

Brand: GE Pages: 32

Brand: Electrolux Pages: 24

Brand: Electrolux Pages: 29

Brand: Electrolux Pages: 16

Brand: FAR Pages: 105

Brand: VALERA Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands