Miele G 7960 C SCVi Operating Instructions Manual Download Page 41

Page: 41 / 124

Settings

Setting the energy tariff times

Before you can use the

EcoStart

option,

you must set at least one energy tariff
time.



Select an energy tariff time to set
from T1 to T3.

The start of the energy tariff time
selected will be displayed.



Set the hours and minutes for the
start time.



Select

Finish

The end of the energy tariff time
selected will be displayed.



Set the hours and minutes for the end
time and confirm both with

The energy tariff time will be saved.

You can now select the priority of the
saved energy tariff time.



Select the priority you want.

The selected settings are displayed.

The energy tariff time will be activated.

Changing the energy tariff times

You can change the start, end or priority
of an energy tariff time.



Select an energy tariff time to change
from T1 to T3.



Select the setting you want to
change.



Change the setting and confirm with

The selected settings are displayed.

The change will be saved.

Summary of Contents for G 7960 C SCVi





























































































































Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands

Miele G 7960 C SCVi, Operating Instructions Manual

Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands