Miele G 7960 C SCVi Operating Instructions Manual Download Page 74

Page: 74 / 124

Options

Setting “Start at”

With the

Start at

function, you set the

exact time you want the programme to
start at.



Set the hours with the



sensor

controls.



Touch the minute number block.



Use the



sensor controls to enter

the minutes and confirm your entry
by touching

The saved start time for the selected
programme will appear in the display for
several minutes.



Close the door.

When the set time is reached, the
selected programme will begin
automatically.

Setting “Finish at”

Use the

Finish at

function to set the

latest time by which the selected
programme has to be finished.



Set the hours with the



sensor

controls.



Touch the minute number block.



Use the



sensor controls to enter

the minutes and confirm your entry
by touching

The estimated start time for the
selected programme will appear in the
display for several minutes.

A message will appear in the display if
the programme cannot be completed
by the set finish time because it has too
long a running time. It will show the
time that can be set.



If it appears, confirm the message
with



Close the door.

The selected programme will start
automatically when the estimated start
time is reached.

Summary of Contents for G 7960 C SCVi





























































































































Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands

Miele G 7960 C SCVi, Operating Instructions Manual

Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands