Miele G 7960 C SCVi Operating Instructions Manual Download Page 99

Page: 99 / 124

Problem solving guide

Door release

Problem

Cause and remedy

The optical in-operation
indicator light is
flashing quickly.
The alarm tone is
sounding.
The following fault is
indicated via the
display:

Before rectifying the problem:



Switch the dishwasher off.



Fault F 33: Open the

door manually. Call Miele
Service

The door does not open automatically.
There may be a technical fault.



Open the door manually (see “Before using for the
first time – Opening the door”) and switch the
dishwasher back on again.



If the same fault message appears again, call the
Miele Customer Service Department.

The door does not close automatically.
The door might be obstructed by an item inside the
appliance.



If this is the case, remove the item causing an
obstruction and switch the dishwasher on again.



If the same fault message appears again, call the
Miele Customer Service Department.

Summary of Contents for G 7960 C SCVi





























































































































Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands

Miele G 7960 C SCVi, Operating Instructions Manual

Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands