Miele G 7960 C SCVi Operating Instructions Manual Download Page 100

Page: 100 / 124

Problem solving guide

100

Water inlet fault

Problem

Cause and remedy

The optical in-operation
indicator light is
flashing quickly.
The alarm tone is
sounding.
One of the following
messages appears in
the display:



Please open the

stopcock

The stopcock is closed.



Open the stopcock fully.



Insufficient water intake.

Open the stopcock fully.
Refer to operating
instructions if necessary

Before rectifying the problem:



Switch the dishwasher off.

The water inlet is restricted.



Open the stopcock fully and start the programme
again.



Clean the filter in the water inlet (see “Cleaning
and care” – Cleaning the filter in the water inlet”).



The water-connection pressure is lower than
50 kPa.
Seek professional advice.



The on-site connection for the water drainage may
be too low and you will need to vent the water
drainage (see “Installation – Water drainage”).



Fault F 18: A technical

fault has occurred. Switch
the appliance off, close the
stopcock and call Miele
Service.

A technical fault has occurred.



Switch the dishwasher off.



Close the stopcock.



Call the Miele Customer Service Department.

The following fault
message appears on
the display during the

SolarSave

programme:

Intake temperature too low

The intake water has not reached the required
temperature of 45 °C (see “Installation – Water inlet”).



Start the programme again.



If the fault message appears again, select a
different programme.

Summary of Contents for G 7960 C SCVi





























































































































Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands

Miele G 7960 C SCVi, Operating Instructions Manual

Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands