background image

Options

75

Setting EcoStart

You can use the 

EcoStart

 function to

benefit from cheaper energy tariffs at
night. Before you can use this option,
you need to set up to three electrical
tariff time zones (see “Settings”
chapter, “EcoStart” section). 
Then set the latest time by which the
selected programme has to be finished
by.
The dishwasher will then start
automatically in the most economical
tariff zone within the time set.

Set the hours with the 



 sensor

controls.

Touch the minute number block.

Use the 



 sensor controls to enter

the minutes and confirm your entry
by touching 

OK

.

The estimated start time for the
selected programme will appear in the
display for several minutes.

Close the door.

The message 

Waiting for EcoStart

 will

appear in the display.

The selected programme will start
automatically when the estimated start
time is reached.

Setting SmartStart

The 

SmartStart

 function is used for

starting your dishwasher automatically
at a time when your energy costs are
most economical.

To use this function you may need
further technical accessories.

If you have activated the

SmartStart

 function in the 

Settings

 menu,

the 

Timer

 

 menu will no longer show

the 

EcoStart

 function but will instead

show 

SmartStart

 (see “Settings” chapter,

“Miele@home” section).

If your energy provider offers this
service, they will send a signal to your
dishwasher when energy costs are at
their most economical.
This signal will start the dishwasher.

You can set the time by which the
selected programme has to be finished
by. The dishwasher will then calculate
the latest possible start time for the
programme selected and will wait until
this start time for the signal from the
energy provider.

Summary of Contents for G 7960 C SCVi





























































































































Reviews: