Miele G 7960 C SCVi Operating Instructions Manual Download Page 103 | Manualshive

Page: 103 / 124

background image

Problem solving guide

103

Problem

Cause and remedy

The optical in-operation
indicator light is
flashing quickly.
At the end of the
programme, the alarm
tone sounds and the
display shows the
following message:



Fault F 601: A fault has

occurred; switch the
appliance off and back on
again. Restart the
programme. If the fault
occurs again, call Miele
Service

.

There is a fault in the AutoDos.



Switch the dishwasher off and back on again.



Check whether the PowerDisk holder and the
PowerDisk have been fitted correctly (see
“Detergent – Automatic dispensing/AutoDos”).



Activate the

AutoDos

function and restart the

programme.

If the fault message appears again, there is a
technical fault. You can continue to use your
dishwasher by deactivating automatic dispensing in
the Extras menu of a programme and manually
dispensing the detergent via the detergent
compartment.



If you wish to use automatic dispensing again,
contact the Miele Customer Service Department.

The optical in-operation
indicator light is
flashing quickly.
At the end of the
programme, the alarm
tone sounds and the
display shows the
following message:

AutoDos requires
maintenance. Please check
AutoDos system.

The dishwasher does
not switch off at the end
of the programme.
The wash items may not
be clean because an
insufficient amount of
detergent was
dispensed.
The

AutoDos

function is

automatically
deactivated during the
programme sequence.

An empty PowerDisk has been inserted or the
AutoDos is blocked by residual detergent. Detergent
dosage is insufficient.
The

AutoDos

function was automatically deactivated.



Switch the dishwasher off and back on again.

Multiple messages appear in the display.



Clean the pouring channel of the AutoDos (see
“Detergent” chapter, “Cleaning the AutoDos”
section).



Clean the lower spray arm (see “Cleaning and
care” chapter, “Cleaning the spray arms” section).



Select

OK

to confirm each message.



Activate the

AutoDos

function by confirming the

message

AutoDos available

using

OK

.



Start the programme again.

The programme duration will be extended by up to
2.5 hours to flush out the AutoDos detergent outlet.

«
...
101
102
103
104
105
...
»

Summary of Contents for G 7960 C SCVi





























































































































Reviews:

No comments

Related manuals for G 7960 C SCVi

Brand: GE Pages: 108

Brand: Haier Pages: 3

Brand: Indesit Pages: 60

FAVORIT 64080 i

Brand: AEG Electrolux Pages: 44

Brand: NEFF Pages: 56

Brand: Smeg Pages: 38

Brand: AT-OS Pages: 60

Brand: Supra Pages: 24

Brand: Progress Pages: 64

Brand: Maytag Pages: 24

Brand: NEFF Pages: 56

Brand: Samsung Pages: 72

Brand: Samsung Pages: 54

Brand: Zanussi Pages: 36

Brand: NEFF Pages: 56

Brand: Indesit Pages: 24

Brand: Candy Pages: 32

Brand: AEG Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands