Miele G 7960 C SCVi Operating Instructions Manual Download Page 33

Page: 33 / 124

Settings

Language



The display can be set to appear in one
of several different languages.

You can change the language used in
the display and also the country via the

Language 

sub-menu.

The flag after the word

Language 

serves as a guide if a language that
you do not understand has been set.
In this case keep selecting the menu
option that has a flag after it until you
reach the

Language 

sub-menu.

Time

The current time of day must be set
before you can use the timer option.

Setting the clock format

You can select either a 24-hour or 12-
hour clock.



Select the setting you want for the
clock format.

Setting the time of day

You can set the current time of day.



Set the hours and the minutes and
confirm by pressing

The time of day has now been saved.

Summary of Contents for G 7960 C SCVi





























































































































Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands

Miele G 7960 C SCVi, Operating Instructions Manual

Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands