Miele G 7960 C SCVi Operating Instructions Manual Download Page 97

Page: 97 / 124

Problem solving guide

Many malfunctions and faults that can occur in daily operation can be easily
remedied. Time and money will be saved because a service call will not be
needed.

The following guide may help you to find the reason for a malfunction or a fault,
and to correct it.

This section only lists faults that you can remedy yourself. All other faults are
shown in



Fault FXX

Technical problems

Problem

Cause and remedy

The dishwasher will not
start.

The door is not closed properly.



Raise the door upwards until the catch engages.

The dishwasher is not plugged in.



Insert the plug and switch on at the socket.

The mains fuse has tripped.



Reset the trip switch in the fuse box or replace the
fuse in the plug (see data plate for minimum fuse
rating).



If the mains fuse trips again, contact the Miele
Customer Service Department.

The dishwasher is not switched on.



Switch the dishwasher on using the



sensor

control.

The dishwasher stops
during a programme.

The mains fuse has tripped.



Reset the trip switch in the fuse box or replace the
fuse in the plug (see data plate for minimum fuse
rating).



If the mains fuse trips again, contact Miele
Service.

After the programme
has started, the optical
in-operation indicator
light is not visible.

The reflector panel was not correctly fitted.



Re-fit the reflector panel correctly (see installation
sheet).

Summary of Contents for G 7960 C SCVi





























































































































Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands

Miele G 7960 C SCVi, Operating Instructions Manual

Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands