Miele G 7960 C SCVi Operating Instructions Manual Download Page 11

Page: 11 / 124

Warning and safety instructions



The plastic housing of the water connection contains a solenoid

valve. The housing must not be dipped in water.



There are live wires in the water inlet hose. Do not cut the hose,

even if it is too long.



The integrated Waterproof system offers protection from water

damage, provided that the following conditions are met:

- Installation has been carried out correctly

- The dishwasher is properly maintained and parts are replaced

where this is noticeably required

- The stopcock is turned off during longer absences from the home

(e.g. whilst on holiday).

The Waterproof system will work even when the dishwasher is
switched off. However, the dishwasher must remain connected to
the electricity supply.



The water-connection pressure needs to be between 50 and

1,000 kPa.



A damaged dishwasher could be dangerous. If the dishwasher

gets damaged, switch it off at the mains immediately and call your
Miele dealer or Miele Service.



While the appliance is under warranty, repairs should only be

undertaken by a Miele authorised service technician. Otherwise the
warranty is invalidated.



We recommend replacing defective components with original

spare parts. If original Miele spare parts are installed correctly, Miele
ensures full compliance with safety requirements and the warranty
remains valid.



During installation, maintenance and repair work, the dishwasher

must be disconnected from the mains electricity supply (switch it off
and withdraw the plug from the socket).

Summary of Contents for G 7960 C SCVi





























































































































Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands

Miele G 7960 C SCVi, Operating Instructions Manual

Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands