Miele G 7960 C SCVi Operating Instructions Manual Download Page 32

Page: 32 / 124

Settings

You can alter the dishwasher’s
controls to suit changing requirements
by adjusting the settings.

The settings can be altered at any
time.

Opening the settings menu



Switch the dishwasher on using the



sensor control.

The Programmes menu will appear in
the display.

For further information about the
display functionality, see the “Display
functions” section in the “Guide to the
appliance” chapter.



Switch to the main menu using the



sensor control.



Touch the

Settings

sensor control.

The display will change to the

Settings

menu.

Changing settings



Select the setting you want to
change.

The selected setting is marked in
orange.



Change the value displayed and
confirm with



Touch an option to select it.



To exit a sub-menu again, use the



Back sensor control.

The display will revert to the menu
above.

Closing the settings menu



Touch the



sensor control.

The display will change to the main
menu.

Summary of Contents for G 7960 C SCVi





























































































































Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands

Miele G 7960 C SCVi, Operating Instructions Manual

Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands