Miele G 7960 C SCVi Operating Instructions Manual Download Page 98

Page: 98 / 124

Problem solving guide

Fault messages

Problem

Cause and remedy

The optical in-operation
indicator light is
flashing quickly.
The alarm tone is
sounding.
One of the following
faults appears in the
display:

Before rectifying the problem:



Switch the dishwasher off.



Fault F XX: A fault has

occurred; switch the
appliance off and back on
again. Restart the
programme. If the fault
occurs again, call Miele
Service

There may be a technical fault.



Switch the dishwasher back on after a few
seconds.



Select the programme you want to use.



Close the door.

If the fault message appears again, there is a
technical fault.



Switch the dishwasher off.



Close the stopcock.



Call the Miele Customer Service Department.



Waterproof fault: Switch

the appliance off, close the
stopcock, call Miele Service.

The Waterproof system has reacted.



Switch the dishwasher off.



Close the stopcock.



Call Miele Service.



Fault F 78: A technical

fault has occurred. Switch
the appliance off, close the
stopcock and call Miele
Service.

Circulation pump fault.



Switch the dishwasher off.



Switch the dishwasher back on.



Select the programme you want to use.



Close the door.

If the fault message appears again, there is a
technical fault.



Switch the dishwasher off.



Close the stopcock.



Call the Miele Customer Service Department.

Summary of Contents for G 7960 C SCVi





























































































































Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands

Miele G 7960 C SCVi, Operating Instructions Manual

Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands