Miele G 7960 C SCVi Operating Instructions Manual Download Page 90

Page: 90 / 124

Cleaning and care

Removing the top spray arm



Push the upper spray arm upwards



to engage the inner ratchet. Then
unscrew the spray arm by rotating the
screw connection anti-clockwise



Removing the middle spray arm



Rotate the screw connection of the
middle spray arm clockwise



and

remove the spray arm



Removing the lower spray arm



Remove the lower basket.



Rotate the screw connection of the
lower spray arm anti-clockwise



and pull the spray arm upwards to
remove



Cleaning the spray arms



Use a pointed object to push food
particles into the spray arm nozzles.



Rinse the spray arm thoroughly under
running water.

Summary of Contents for G 7960 C SCVi





























































































































Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands

Miele G 7960 C SCVi, Operating Instructions Manual

Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands