Miele G 7960 C SCVi Operating Instructions Manual Download Page 96

Page: 96 / 124

Cleaning and care

The drain pump (see arrow) is
underneath the cover.



Risk of injury from glass

splinters.
It is especially difficult to see glass
splinters in the drain pump.
Take care when cleaning the drain
pump.



Carefully remove all foreign objects
from the drain pump. Check the drain
pump impeller by manually turning it.
You will feel a little resistance when
you turn the impeller.



Refit the cover by placing it down
vertically from above.

Ensure that the catch engages
correctly.



Damage due to incorrect

cleaning.
The components are delicate and
can be damaged during cleaning.
Take care when cleaning the drain
pump.

Summary of Contents for G 7960 C SCVi





























































































































Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands

Miele G 7960 C SCVi, Operating Instructions Manual

Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands