Miele G 7960 C SCVi Operating Instructions Manual Download Page 26 | Manualshive

Page: 26 / 124

background image

Before using for the first time

26

Activating AutoDos

The display changes to the settings
screen for AutoDos (see the “Detergent”
chapter, “Automatic dispensing/
AutoDos” section).

Even if you do not wish to use
AutoDos, you must remove the
transport locking device from the
PowerDisk compartment before
running the first programme (see the
“Detergent” chapter, “Activating
AutoDos” section).

You can activate AutoDos.
If you do not wish to use AutoDos
(automatic dispensing), you can
manually dispense the detergent via the
detergent compartment (see the
“Detergent” chapter, “Manual detergent
dispensing” section).



Select the setting you want and
confirm with

OK

.

This setting applies to all programmes
and you can change it in a
programme's Extras menu.

«
...
24
25
26
27
28
...
»

Summary of Contents for G 7960 C SCVi





























































































































Reviews:

No comments

Related manuals for G 7960 C SCVi

Brand: lamber Pages: 52

Brand: Gaggenau Pages: 22

Brand: Gaggenau Pages: 34

Brand: Rangemaster Pages: 28

Brand: BALAY Pages: 2

Brand: Amana Pages: 24

Brand: Zanussi Electrolux Pages: 28

Brand: Kärcher Pages: 44

Brand: Heinner Pages: 59

Brand: V-ZUG Pages: 48

AdorinaWash V400

Brand: V-ZUG Pages: 20

Brand: Hansa Pages: 40

Brand: Hansa Pages: 38

Brand: Samsung Pages: 22

Brand: Samsung Pages: 28

Brand: Samsung Pages: 88

WF-B105N(V/C/S)

Brand: Samsung Pages: 22

Brand: Samsung Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands