Miele G 7960 C SCVi Operating Instructions Manual Download Page 87

Page: 87 / 124

Cleaning and care

Cleaning the AutoDos

You should regularly check (about
every 2–3 months when the
PowerDisk is empty) that the pouring
channel is clean, and clean it if
necessary. This helps keep the
AutoDos working properly.

In order to ensure that the AutoDos
works at its best, check it each time
you replace the PowerDisk and clean
it if needed.

PowerDisk holder

Pouring channel for dispensing the

detergent from the PowerDisk into the
wash cabinet



Turn the AutoDos lid to



and open

it.



Remove the PowerDisk if appropriate.



Pull the PowerDisk holder upwards
by the yellow tabs and remove it.
When doing so, do not pull on the
side tab.



Use the tab (see arrow)



to release

the pouring channel and pull it out



Summary of Contents for G 7960 C SCVi





























































































































Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands

Miele G 7960 C SCVi, Operating Instructions Manual

Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands