Miele G 7960 C SCVi Operating Instructions Manual Download Page 68

Page: 68 / 124

Operation

Switching on the dishwasher



Open the stopcock, if it is closed.



Open the door.



Make sure the spray arms can rotate
freely.



Touch the



sensor control.

If the dishwasher has been switched
off for longer than 1 minute, you will
need to hold the



sensor control for

a bit longer (wipe protection).

The Programmes menu will appear in
the display.

Selecting a programme

Choose your programme according to
the type of crockery and the degree of
soiling.

The different programmes and their
uses are described under “Programme
overview”.



Select the programme you want in
the display.

The display will change to the Extras
menu.

You can now select the extras (see
“Extras”).

To select a different programme, touch
the



sensor control to return to the

Programmes menu.

Summary of Contents for G 7960 C SCVi





























































































































Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands

Miele G 7960 C SCVi, Operating Instructions Manual

Search results

Summary of Contents for G 7960 C SCVi

Reviews:

Related manuals for G 7960 C SCVi

Brands by name

Popular brands