Miele G 6994 Operating Instructions Manual Download Page 75

Page: 75 / 116

Cleaning and care

Cleaning the spray arms

Particles of food can get stuck in the
spray arm jets and bearings. The spray
arms should therefore be inspected and
cleaned regularly (approx. every 4 - 6
months).



Switch the dishwasher off.

Remove the spray arms as follows:



Take out the cutlery tray (if your
dishwasher is fitted with one).



Push the

top

spray arm upwards to

engage the inner ratchet. Then
unscrew the spray arm.



Push the

middle

spray arm upwards



to engage the ratchet. Then

unscrew the spray arm





Remove the lower basket.



Pull the

lower

spray arm firmly

upwards to remove it.



Use a pointed object to push food
particles into the spray arm jets.



Rinse thoroughly under running
water.



Refit the spray arms and check that
they rotate freely.

Summary of Contents for G 6994





















































































































Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands

Miele G 6994, Operating Instructions Manual

Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands