Miele G 6994 Operating Instructions Manual Download Page 30 | Manualshive

Page: 30 / 116

background image

Before using for the first time

30



Add rinse aid only until it is visible in
the opening.

The rinse aid reservoir holds approx.
110 ml.



Close the flap firmly so that it clicks
into place. Otherwise water can enter
the rinse aid reservoir during a
programme.



Wipe up any spilled rinse aid. This
prevents over-foaming occurring
during the next programme.

You can adjust the rinse aid dosage
for best results (see "Settings menu -
Rinse aid").

Add rinse aid reminder

When the



Insufficient rinse aid

message appears in the display, the
reservoir contains sufficient rinse aid for
2 - 3 programmes only.



Add rinse aid in plenty of time.



Confirm with

OK

.

The message will go out.

If you only ever use multi-function
combination products in your
dishwasher, you can switch off both
refill reminders for salt and rinse aid if
you wish (see "Settings menu -
Switching off the refill reminders").

If you switch to using detergent that
does not contain salt or rinse aid, it
is important to remember to add
dishwasher salt and rinse aid and to
switch the reminders back on.

«
...
28
29
30
31
32
...
»

Summary of Contents for G 6994





















































































































Reviews:

No comments

Related manuals for G 6994

Brand: Magic Chef Pages: 12

HG4585D107636QW

Brand: Hanseatic Pages: 82

Brand: Maytag Pages: 10

Brand: Hotpoint Pages: 12

Brand: Hotpoint Ariston Pages: 24

Brand: Gorenje Pages: 29

3VT913NA - annexe 1

Brand: BALAY Pages: 2

DDW1802 - 14352

Brand: Danby Pages: 12

Brand: Supra Pages: 24

Brand: Samsung Pages: 47

WF435ATGJWR/A1-0002

Brand: Samsung Pages: 144

Brand: Samsung Pages: 228

Brand: Samsung Pages: 276

Brand: Samsung Pages: 7

Brand: Frigidaire Pages: 2

Brand: Frigidaire Pages: 12

Brand: Frigidaire Pages: 7

Brand: Frigidaire Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands