Miele G 6994 Operating Instructions Manual Download Page 111

Page: 111 / 116

Settings menu

111

Software version

You can call up the electronic software
version of your dishwasher for technical
support purposes.



Confirm the display with

Showroom programme

For demonstration purposes only.

The dishwasher is fitted with various
demonstration programmes for
showroom use.

–

Demo mode

Programme for use in showrooms to
demonstrate the TimeControl
function.

–

Demo with sound

This programme activates the
circulation pump to demonstrate the
sound of the dishwasher.

–

Demo AutoOpen

The door will open automatically.

–

Cont. BrilliantLight

The interior lighting is on constantly.

Factory default settings

You can reset all dishwasher settings to
the factory default settings.

You will be given the choice of

Appliance

settings

Main menu

Wi-Fi module settings have to be reset
separately.



Select the one you would like to
reset.



Confirm the message

Reset settings?

Reset main menu?

with

Yes

Closing the Settings menu

To close the

Settings 

menu, use the



sensor. This will take you back to the

main menu.

Summary of Contents for G 6994





















































































































Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands

Miele G 6994, Operating Instructions Manual

Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands