Miele G 6994 Operating Instructions Manual Download Page 108

Page: 108 / 116

Settings menu

108

Volume

A sequence of audible tones will sound
at the end of the programme or if there
is a fault as long as the buzzer has been
activated.

Buzzer in the event of a fault

The buzzer in the event of a fault will
sound four times at intervals with a
short pause between each set of tones.

The buzzer which sounds when there
is a fault cannot be deactivated.

Buzzer at the end of a programme

The buzzer at the end of a programme
will sound four times at intervals with a
short pause between each set of tones.

Buzzer tones

The volume of the tone at the end of the
programme can be selected in seven
stages or switched off.



Select the volume you want using the

Quieter

and

Louder

options, or switch

the buzzer off.



Confirm with

Night time buzzer tone

You can select a different volume for
the buzzer at night, or switch it off.



Select the volume you want for the
night time buzzer using the

Quieter

and

Louder

options, or switch the

night time buzzer off.



Confirm with

Night time

You can select the times for night time
to begin and end.



Select the

Start at

option.



Use the



arrow sensors to set the

time in hours and minutes for the
night time to begin and confirm both
with



Select the

Finish at

option.



Use the



arrow sensors to set the

time in hours and minutes for the
night time to end and confirm both
with

Keypad tone

An audible tone sounds each time a
sensor is pressed.

The volume for the keypad tone can be
set in seven stages, or switched off.



Select the volume you want using the

Quieter

and

Louder

options, or switch

the keypad tone off.



Confirm with

Summary of Contents for G 6994





















































































































Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands

Miele G 6994, Operating Instructions Manual

Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands