Miele G 6994 Operating Instructions Manual Download Page 64

Page: 64 / 116

Programme options

Set the time, by which the selected
programme has to be finished by.



Use the



arrow sensors to set the

hour and confirm with

The hour will be saved and the minute
number block will be highlighted.



Use the



arrow sensors to set the

minutes and confirm with

Waiting for SmartStart

will appear in the

display.



Close the door.

The left-hand TimeControl in-operation
indicator light will start flashing.

The selected programme will start
automatically as soon as the energy
provider has sent the signal, or the
latest calculated start time has been
reached.

Changing or deleting set times

You can change the set times or the
programme before the start time in the
display is reached.



Open the door.



Press the



sensor.



Select the function for which you
want to change or delete the time.

After confirming the

Change

option, you

can change the set time.

After confirming the

Delete

option, the

set time will be deleted and the



indicator light will go out.

You can now select and start a
programme.

Summary of Contents for G 6994





















































































































Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands

Miele G 6994, Operating Instructions Manual

Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands