Miele G 6994 Operating Instructions Manual Download Page 97

Page: 97 / 116

Settings menu

Settings menu for changing
standard settings

Opening the Settings menu



Switch the dishwasher on with the



sensor if it is switched off.

The main menu will appear in the
display.
If the Memory function is activated, the
programme menu for the programme
last selected will be displayed instead
(see "Settings - Memory"). If this is the
case, use the



sensor to get to the

main menu.

To learn about the display, read the
section with the same name.



Select the

Settings 

option.

The display will change to show the

Settings 

menu.



Select the option you want to
change.

Press the



sensor to call up more

information about the programme
currently selected.

Sub-menu options which have already
been selected will have a tick



beside them.



To exit a sub-menu again, use the



sensor.

The display will revert to the menu
above.

Summary of Contents for G 6994





















































































































Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands

Miele G 6994, Operating Instructions Manual

Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands