Miele G 6994 Operating Instructions Manual Download Page 105

Page: 105 / 116

Settings menu

105

Remote control

Once you have installed the
Miele@mobile App on your tablet PC or
your Smartphone, you will be able to
operate your dishwasher remotely. Your
dishwasher must be signed on to a Wi-
Fi network and the

Remote

control

function must be activated.



Select the setting you want and
confirm with



Touch the



sensor twice to return

to the main menu.

After activating the

Remote control

function, the

MobileControl

option will

appear in the display.

In order to operate the dishwasher with
the Miele@mobile App, please activate
the

MobileControl

function.



Select the

MobileControl

option.



Confirm the message with

and

close the door.

The left-hand TimeControl in-operation
indicator light will start flashing.

The dishwasher can now be operated
remotely using the Miele@mobile App.

If you now do not wish to operate the
dishwasher remotely with the
Miele@mobile App, you can cancel the

MobileControl

function.



Open the door.



Select

Cancel

and confirm with

Yes

Summary of Contents for G 6994





















































































































Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands

Miele G 6994, Operating Instructions Manual

Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands