Miele G 6994 Operating Instructions Manual Download Page 58 | Manualshive

Page: 58 / 116

background image

Operation

58

Interrupting a programme

A programme is interrupted as soon as
the door is opened.
If the door is closed again, the
programme will continue from the point
it was at before the door was opened.



Water in the dishwasher may be

hot. Danger of scalding!
Only open the door if absolutely
necessary and exercise extreme
caution when doing so. Before
closing the door again, leave it ajar
for approx. 20 seconds. This will
enable the temperature in the wash
cabinet to settle. Then raise the door
up and push until the catch engages.

Changing a programme

If the detergent dispenser flap has
already opened, do not change the
programme.

If a programme has already started and
you wish to change it, proceed as
follows:



Open the door.



Press the Back sensor



.



Confirm the message

Cancel

programme?

with

Yes

.

The programme will be cancelled.



Select the Main menu option.

The display will revert to the main
menu.



Select the programme you want, and
then start it by shutting the door.

The In-operation indicator comes on to
show that a programme has been
started.

«
...
56
57
58
59
60
...
»

Summary of Contents for G 6994





















































































































Reviews:

No comments

Related manuals for G 6994

Brand: Washtech Pages: 44

Brand: Haier Pages: 14

Brand: Haier Pages: 2

Brand: Candy Pages: 30

Brand: Samsung Pages: 5

Brand: American Dish Service Pages: 32

Brand: Modular Pages: 97

EPIC Z MHWZ400TB02

Brand: Maytag Pages: 60

Brand: Metos Pages: 52

DDW24T99 Series

Brand: Dacor Pages: 156

Brand: elvita Pages: 158

Brand: Jet-tech Pages: 10

Brand: Magic Chef Pages: 12

Brand: Meiko Pages: 48

Brand: unicraft Pages: 18

Brand: Danby Pages: 56

Brand: Gorenje Pages: 36

Brand: V-ZUG Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands