Miele G 6994 Operating Instructions Manual Download Page 102

Page: 102 / 116

Settings menu

102

Changing the electricity tariff times

You can change the start, finish or
priority of an electricity tariff time.



Select an electricity tariff time from
T1-T3 to change.



Select the setting you want to
change.



Use the



arrow sensors to change

the setting and confirm with

The change will be saved.

Deleting the electricity tariff times



You can delete the settings for an
electricity tariff time and in doing so
deactivate the

EcoStart

option for this

time zone.



Select an electricity tariff time from
T1-T3 to delete.



Select

Delete



Confirm the query

Delete tariff T1?

with

Delete

The settings for the electricity tariff time
selected will be reset.



Confirm the message with

The electricity tariff time has now been
deleted.

Summary of Contents for G 6994





















































































































Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands

Miele G 6994, Operating Instructions Manual

Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands