Miele G 6994 Operating Instructions Manual Download Page 79

Page: 79 / 116

Problem solving guide

Water inlet fault

Problem

Possible cause and remedy

All TimeControl in-
operation indicators are
flashing quickly.
The warning buzzer is
sounding.
One of the following
faults appears in the
display:



Water inlet fault. Please

open the stopcock

The tap is turned off.



Turn on the tap fully.



Water inlet fault

Before rectifying the problem, you must:



Switch the dishwasher off using the



sensor.

Water intake is restricted.



Turn on the tap fully and start the programme
again.



Clean the water inlet filter (see "Maintenance").



The water pressure at the intake is lower than 50
kPa (0.5 bar).
Seek professional advice.

The following message
appears in the display
during the

SolarSave

programme:



Water in. temp. too low

The intake water has not reached the required
temperature of 45°C (see "Water connection -
Connection to the water supply").



Start the programme again.



If the fault message appears again, select a
different programme.

Summary of Contents for G 6994





















































































































Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands

Miele G 6994, Operating Instructions Manual

Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands