Miele G 6994 Operating Instructions Manual Download Page 77

Page: 77 / 116

Problem solving guide

Problem

Possible cause and remedy

All in-operation
indicators are flashing
quickly.
The warning buzzer is
sounding.
One of the following
faults appears in the
display:

Before rectifying the problem, you must:



Switch the dishwasher off using the



sensor.



Technical fault FXX

There may be a technical fault.

After a few seconds:



Switch the dishwasher back on.



Select the programme you want.



Close the door.

If the fault message appears again, there is a
technical fault.



Call Miele.



Waterproof fault

The Waterproof system has reacted.



Turn off the tap.



Call Miele.



Technical fault F78

A fault has occurred in the circulation pump.



Switch the dishwasher off for at least 30 seconds
with the



sensor.



Switch the dishwasher back on.



Select the programme you want.



Close the door.

If the fault message appears again, there is a
technical fault.



Call Miele.

Summary of Contents for G 6994





















































































































Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands

Miele G 6994, Operating Instructions Manual

Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands