Miele G 6994 Operating Instructions Manual Download Page 98

Page: 98 / 116

Settings menu

Language



The display can be set to appear in one
of several different languages.

You can change the language in the
display via the

Language 

sub-menu.



Select the language you want and
confirm this with

Some languages also have a country
option to select.



If so, select the appropriate country
and confirm your selection with

The flag after the word

Language 

acts as a guide if a language which
you do not understand has already
been set.
If this is the case, keep selecting the
option which has a flag after it until
you reach the

Language 

sub-menu.

Time of day

The current time of day must be set
before you can use the

Delay start

option.

Setting the clock format

You can select either a 24-hour or 12-
hour clock.



Select the

Clock format

option.



Select the setting you want and
confirm with

Setting the time of day



Select the

Set

option.



Set the hour with the



arrow

sensors and confirm with

Then set the minutes and confirm
with

The time of day has now been saved.

Summary of Contents for G 6994





















































































































Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands

Miele G 6994, Operating Instructions Manual

Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands