Miele G 6994 Operating Instructions Manual Download Page 16 | Manualshive

Page: 16 / 116

background image

Warning and Safety instructions

16

Correct installation



The dishwasher must be installed and connected in compliance

with the installation instructions.



Be careful when installing the dishwasher. Wear

protective gloves to avoid injury on any sharp metal
components.



The dishwasher must be correctly aligned to ensure problem-free

operation.



In order to ensure stability, built-under and integrated dishwashers

must only be installed under a continuous worktop which is secured
to adjacent cabinetry.



If you want to convert your freestanding dishwasher to a built-

under ("U") model, you will need to order the appropriate conversion
kit. If you remove the existing plinth, you must replace it with a U-
model plinth. This is necessary to avoid the risk of injury caused by
protruding metal parts.



The door springs on either side need to be evenly adjusted. They

are correctly adjusted if the half-opened door (approx. 45° door
opening angle) remains in this position when it is released. The door
must not fall down under its own weight.
The appliance may only be used with correctly adjusted door
springs.

«
...
14
15
16
17
18
...
»

Summary of Contents for G 6994





















































































































Reviews:

No comments

Related manuals for G 6994

Brand: EAS Electric Pages: 194

Brand: Haier Pages: 20

Brand: Alliance Laundry Systems Pages: 32

Brand: Hoonved Pages: 18

Brand: Manta Pages: 19

Brand: Avanti Pages: 56

Brand: Indesit Pages: 24

Brand: Admiral Pages: 32

EVA-VX 5.5; Elena Aqua SX 6.0

Brand: IFB Pages: 25

Brand: Hoover Pages: 36

Brand: Proline Pages: 16

Brand: unicraft Pages: 18

Brand: Danby Pages: 56

Brand: Indesit Pages: 84

Brand: Bush Pages: 38

WA16T6260 Series

Brand: Samsung Pages: 44

WA19CG6886 Series

Brand: Samsung Pages: 52

WA18CG6886 Series

Brand: Samsung Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands