Miele G 6994 Operating Instructions Manual Download Page 57 | Manualshive

Page: 57 / 116

background image

Operation

57

Switching off

At the end of a programme:



Open the door.



The dishwasher can be switched off
at any time using the



sensor.

Switching the dishwasher off during a
programme cancels the programme.

Switching the dishwasher off during the
run-up to a Delay start time will also
stop the process.

If the dishwasher is not going to be
used for a longer period of time, e.g.
whilst on holiday, the tap should be
turned off.

Unloading the dishwasher

Dishes tend to break and chip more
easily when they are hot. Allow the
dishes to cool until they are comfortable
enough to handle before unloading
them.

If you open the door fully after switching
off, the dishes will cool much faster.

First unload the lower basket, then the
upper basket and finally the cutlery tray
(depending on model).
This will prevent water drops from the
upper basket and cutlery tray from
falling onto the dishes in the lower
basket.

«
...
55
56
57
58
59
...
»

Summary of Contents for G 6994





















































































































Reviews:

No comments

Related manuals for G 6994

Brand: Blomberg Pages: 43

Upright Door Dishmachines Tempstar Series

Brand: Jackson Pages: 103

Brand: American Dish Service Pages: 32

Brand: Dawlance Pages: 4

YWNE52PP113TW01

Brand: Alliance Laundry Systems Pages: 50

Brand: Smeg Pages: 35

Brand: Infiniton Pages: 67

Brand: Newworld Pages: 41

Brand: Hallman Pages: 39

Brand: Electrolux Pages: 40

Brand: Electrolux Pages: 24

Brand: Electrolux Pages: 44

Brand: Electrolux Pages: 36

Brand: Electrolux Pages: 44

Brand: Electrolux Pages: 48

Brand: Electrolux Pages: 52

Brand: Electrolux Pages: 52

Brand: Electrolux Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands